Call Disconnect and Progress Codes Click here for RADIUS Attributes
Table of Contents
This document includes the Call Disconnect and Progress Codes in the MAX unit, software version 6.0.10 and 6.1.9 and TNT version 2.0.10 and 2.1.9. These codes are recorded in Syslog, Radius Accounting, Call-Logging, and in the System Log.
MAX 1800, 20xx, 40xx, 60xx, TNT, and dslTNT units
Call Disconnect Cause and Progress Codes
| Disconnect Cause | Code | Progress | Code |
| No-Reason -could not be determined | 0 | Not applied to any call | 1 |
| Not Applicable - unknown | 1 | Unknown progress | 2 |
| Unknown - Catch all | 2 | ||
| Call Disconnected | 3 | Call detected and accepted | 10 |
| CLID authentication failed | 4 | ||
| CLID Radius Timeout | 5 | Modem assigned to call | 30 |
| Successful authentication. Callback configured | 6 | Modem is awaiting DCD from far-end | 31 |
| Pre-T310 Send Disc timer triggered | 7 | Modem is awaiting result codes from far-end | 32 |
| No modem is available to accept call | 9 | ||
| Modem never detected DCD | 10 | Term server session started (needn't be logged in) | 40 |
| DCD detected; but went inactive | 11 | Started raw TCP | 41 |
| Couldn't parse modem result codes | 12 | Started immediate telnet | 42 |
| Failed to open a modem for outgoing call. | 13 | Raw TCP connected to host | 43 |
| Failed to open a modem for outgoing call while modemdiag diagnostic command is enabled | 14 | Telnet connected to host Rlogin started | 44 45 |
| Rlogin connect | 46 | ||
| TermSrv - normal user exit | 20 | Terminal server authentication started | 47 |
| TermSrv - timeout waiting for input | 21 | ||
| TermSrv - exiting Telnet forces disconnect | 22 | Call is active on a modem outdial session | 50 |
| TermSrv - no IP address available for switching to a framed protocol (eg. SLIP,PPP) | 23 | Outing/bridging session up | 60 |
| TermSrv - exiting raw TCP forces disconnect | 24 | Opening LCP | 61 |
| TermSrv - exceeded maximum login attempts | 25 | Opening CCP | 62 |
| TermSrv - attempt to raw TCP when it is disabled | 26 | Opening IPNCP | 63 |
| TermSrv - received Control-C during login | 27 | Opening Bridging NCP | 64 |
| TermSrv - session cleared ungracefully | 28 | LCP in Open state | 65 |
| TermSrv - normal user close of virtual connect | 29 | CCP in Open state | 66 |
| TermSrv - Originating end terminated (controlling | 30 | IP NCP in Open state | 67 |
| terminal server session went down). | Bridging NCP in Open state | 68 | |
| TermSrv - Rlogin exiting | 31 | ||
| TermSrv - bad Rlogin option specified | 32 | Progress Of LCP Negotiations | |
| TermSrv - not enough resources | 33 | (See RFC1331 State Transition Table): | |
| MPP - NULL msg timeout. Null MP packets are | 35 | LCP in Initial state | 69 |
| sent (and received) on each channel | LCP in Starting state | 70 | |
| throughout an MP+ session. | LCP in Closed state | 71 | |
| LCP in Stopped state | 72 | ||
| PPP - LCP timed out waiting for a response | 40 | LCP in Closing state | 73 |
| PPP - failure to converge on LCP negotiations | 41 | LCP in Stopping state | 74 |
| PPP - PAP authentication failed | 42 | LCP in Req-Sent state | 75 |
| PPP - CHAP authentication failed | 43 | LCP in Ack-Rcvd state | 76 |
| PPP - authentication failed from remote server | 44 | LCP in Ack-Sent state | 77 |
| PPP - LCP got Terminate request from far-end | 45 | ||
| while LCP was in Open state | IPX NCP in Open state | 80 | |
| PPP - LCP got Close request from upper layer | 46 | AT NCP Opened | 81 |
| while LCP was in Open state (normal | BACP Opening | 82 | |
| graceful LCP closure) | BACP Opened | 83 | |
| PPP - Closing LCP - no NCPs were opened | 47 | CBCP being opened | 84 |
| PPP - Closing LCP - MP bundle unknown | 48 | CBCP is now open | 85 |
| PPP - Closing LCP - MP can't add more channels | 49 | ||
| V.110 call accepted | 90 | ||
| /* Following are errors for Telnet and raw TCP */ | V.110 in opened state | 91 | |
| Session tables full | 50 | V.110 in carrier state | 92 |
| No more resources | 51 | V.110 in reset state | 93 |
| IP address is invalid | 52 | V.110 in closed state | 94 |
| Cannot resolve hostname | 53 | ||
| Bad or missing port number | 54 | Ascend unit determines that call requires callback | 100 |
| Host reset | 60 | Authentication failed | 101 |
| Connection was refused | 61 | Remote authentication server timed out | 102 |
| Connection timed out | 62 | ||
| Connection closed by foreign host | 63 | Frame Relay link inactive, negotiate in progress | 120 |
| Network unreachable | 64 | Frame Relay link active, end-to-end connectivity | 121 |
| Host unreachable | 65 | ||
| Network admin unreachable | 66 | ||
| Host admin unreachable | 67 | ||
| Port unreachable | 68 | ||
| Session timeout | 100 | ||
| Invalid incoming user / LAN Security Error | 101 | ||
| Disconnect due to callback enabled | 102 | ||
| Instigating call no longer active | 115 | ||
| Requested protocol disabled/unsupported | 120 | ||
| Disconnect requested by RADIUS | 150 | ||
| Disconnect by Local Admin | 151 | ||
| Call disconnected via SNMP | 152 | ||
| Timeout, sync retries exceed max V.110 retries | 160 | ||
| Timeout waiting to authenticate | 170 | ||
| User executed 'Do.Hangup' | 180 | ||
| Call cleared by system | 181 | ||
| Remote End Hung Up - Signal lost from far end | 185 | ||
| Resource has been Quiesced | 190 | ||
| MAX Call duration reached | 195 | ||
| Ascend unit has low memory | 201 | ||
| Slot Card Down | 210 | ||
| Ascend requires CBCP, but no client support | 220 | ||
| Ascend unit deleted VROUTER | 230 | ||
| Ascend unit disconnected call on the basis of LQM measurements | 240 | ||
| Ascend unit cleared backup call | 241 | ||